11-25-2009 08:47 AM
- When I clicked evrc-b my phone couldn't make calls it just kept popping up "call lost". So I tried 13k and it works. Is there something I have to do to get evrc-b to work? Or should I stick with 13k or back to the default evrc? Which one is the best one to use of the three?11-15-2009 02:27 PM
- LOL. I was wondering where all the posts went.
For all those that are confused, they are discussing changing the vocode setting by doing the following:
To get into the programming menu, from the call screen enter ##PROGRAM and press send. Enter code 000000 In option 04, you can change the vocode option to EVRC-B, or 13K, it made my in-call audio sound better. Your phone will reset after you exit and apply the new setting.
Warning: Use caution when in the programming menu, you could potentially brick your phone.11-15-2009 11:53 PM
- I've set mine at EVRC-B... voice quality is very good.. I've also heard that 13k is better than plain 'ol EVRC.
QCELP (13k) (Qualcomm Code Excited Linear Prediction), also known as Qualcomm PureVoice, is a speech codec developed in 1994 to increase the speech quality of the IS-96A codec used earlier in CDMA networks. It was replaced later with EVRC since it provides better speech quality with fewer bits. There are two versions available: QCELP8 and QCELP13 and they use 8 and 13 Kbit/s respectively.
Enhanced Variable Rate CODEC (EVRC) is a speech codec used in CDMA networks. It was developed in 1995 to replace the QCELP vocoder which used more bandwidth on the carrier's network, thus EVRC's primary goal was to offer the mobile carriers more capacity on their networks while not increasing the amount of bandwidth or wireless spectrum needed.. EVRC uses RCELP technology, which Qualcomm claims improves speech quality with lower bit rates
Enhanced Variable Rate Codec B (EVRC-B) is a speech codec used by CDMA networks. EVRC-B is an enhancement to EVRC and compresses each 20 milliseconds of 8000 Hz, 16-bit sampled speech input into output frames of one of the four different sizes: Rate 1 - 171 bits, Rate 1/2 - 80 bits, Rate 1/4 - 40 bits, Rate 1/8 - 16 bits.11-18-2009 11:44 AM
- To get into the programming menu, from the call screen, enter ##PROGRAM and press send. Enter code 000000.
In option 04, you can change the vocode option to EVRC-B, or 13K, it made my in-call audio sound better. I'm currently using the 13K setting. Your phone will reset after you exit and apply the new setting.
Warning: Be careful what options you change in the programming menu, you could potentially brick your phone.
Edit: Forgot to give the code of 000000 to enter at activation screen.
Option 5 -> Data Rates
Mine is set to 153.6/9.6. I am guessing these are down/up speeds? There is an option for 153.6/153.6. Lets see if it makes a difference.11-18-2009 10:21 PM
- From what I've read on a thread on the Motorola site not all areas of the country have EVRC-B therfore you won't be able to make calls so your stuck with EVRC or 13k until they make the upgrade. My wife was complaining about the poor quality on my new Droid and I changed it to EVRC-B and now it works great. I travel alot so I texted the programming instructions to myself in case I'm in an area that doesn't support EVRC-B if I need to change it back to EVRC.11-20-2009 10:00 AM
- I also experienced the phone not working on EVRC-B. When I switched to 13K the callers sound much clearer but if there is any background noise on the caller's end it is extremely loud. I was on the phone with someone today who was shuffling papers at their desk and that noise came through loud and clear. My phone is back on EVRC. Interestingly, I swapped out my first Droid 2 days ago for the same problem (muffled caller voice and loud background noises).11-20-2009 11:45 PM
- Motorola Android Phones
- More Motorola Phones
- Verizon Droid Forums
- Motorola Droid
LINK TO POST COPIED TO CLIPBOARD