So recently, I was given a GS4 SGH-I337 that had been continually rebooting into the Odin Mode screen. After several attempts from me and a friend, I couldn't resolve the issue at hand with most solutions nor was Kies worth any help at all.
Odin Logs:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MK2_Full_Odin_Tar.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when I boot into Odin Mode on the device, I'm greeted with these:
ODIN MODE
Product Name: SGH-I337
Current Binary: Samsung Official
System Status: Official
KNOX Kernel Lock: 0x0
KNOX Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enable
eMMC Burst Mode: enabled
START [224,1440]
SW REV. CHECK FAIL: fused : 5, Binary: 4
So I'm confused as to where to proceed from here. I unfortunately have no clue as to whether or not the device has been upgraded, but obviously, it's been messed with judging from the void flag being tripped.
Odin Logs:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MK2_Full_Odin_Tar.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And when I boot into Odin Mode on the device, I'm greeted with these:
ODIN MODE
Product Name: SGH-I337
Current Binary: Samsung Official
System Status: Official
KNOX Kernel Lock: 0x0
KNOX Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enable
eMMC Burst Mode: enabled
START [224,1440]
SW REV. CHECK FAIL: fused : 5, Binary: 4
So I'm confused as to where to proceed from here. I unfortunately have no clue as to whether or not the device has been upgraded, but obviously, it's been messed with judging from the void flag being tripped.
Facebook
Twitter
Instagram