10-25-2011 01:22 PM
38 12
tools
  1. t0t's Avatar
    Guys, got Question, will doing a hard reset ora factory reset undo these 4g changes?
    09-24-2011 05:21 AM
  2. taylormah's Avatar
    Guys, I think I changed some other settings by mistake like ExitCNR and ExitDelay. Can someone please post all of their original values in Wimax->Extensions screen like ScanAttemptTimeOut, ScanRetries, IdleSleep, EntryDelay, ExitCINR, ExitDelay. Thanks!!
    09-28-2011 01:50 AM
  3. sndplace's Avatar
    Guys, I think I changed some other settings by mistake like ExitCNR and ExitDelay. Can someone please post all of their original values in Wimax->Extensions screen like ScanAttemptTimeOut, ScanRetries, IdleSleep, EntryDelay, ExitCINR, ExitDelay. Thanks!!
    ScanAttemptTimeOut 00002
    ScanRetries 00120
    IdleSleep 00010
    EntryDelay 00300
    ExitCINR 00002
    ExitDelay 00002
    taylormah likes this.
    09-28-2011 05:19 AM
  4. Psychosaturn's Avatar
    Did this but said my Wimax is disconnected. How do I connect it back?
    09-28-2011 08:46 AM
  5. xtn's Avatar
    Did this but said my Wimax is disconnected. How do I connect it back?
    Turn on 4g someplace you get a decent signal.

    xtn
    09-28-2011 10:07 AM
  6. Psychosaturn's Avatar
    Oh so you have to have a 4G signal. I only have 3G where I live. I worried a bit since am almost two weeks learning about Android. Thought I messed up my settings. I did do the 3G fix and so far seems like it gave me a boost. We will see in the long run.
    09-28-2011 10:37 AM
  7. xtn's Avatar
    Oh so you have to have a 4G signal. I only have 3G where I live. I worried a bit since am almost two weeks learning about Android. Thought I messed up my settings. I did do the 3G fix and so far seems like it gave me a boost. We will see in the long run.
    Yes, the setting changes for 4G won't stick unless you're connected to 4G when you make them.

    xtn
    Psychosaturn likes this.
    09-28-2011 11:18 AM
  8. Nonja's Avatar
    Can someone help me out with finding my MSL code using ConnectBot (or another program)? I followed the instructions in the Softpedia article, but what I thought was my MSL code (the only 6 digit number I could find) didn't work.

    What I thought was my MSL code showed up in ConnectBot, after typing "getprop", next to [gsm.operator.numeric]. The number was purely numeric, no letters.
    09-28-2011 01:43 PM
  9. xtn's Avatar
    The MSL is numbers only.

    Sent from my SPH-D710 using Tapatalk
    09-29-2011 08:18 AM
  10. Nonja's Avatar
    The MSL is numbers only.

    Sent from my SPH-D710 using Tapatalk
    I found a thread that out lines it step by step. Thanks
    09-29-2011 08:29 AM
  11. boe's Avatar
    Does anyone know how to get to the 4G settings on the Epic Touch 4G? I turned on Wimax before dialing ##3282# I can view or edit. I select edit and put in my MSL. From there, my choices are
    Data Profile
    EVDO
    Advanced
    USB Charging
    Others

    I've changed my proxy settings by going to others, but I don't see anything for wimax. I've looked under each selection but don't seem to find it.
    10-23-2011 06:31 PM
  12. Capp5050's Avatar
    BUMP! (me too)
    10-25-2011 12:58 PM
  13. Capp5050's Avatar
    BUMP! (me too)
    NEVER MIND!

    On the Epic 4G Touch, when the first menu comes up, select 'View' (not Edit) , and when you get to the field you want to change, hold it down until 'Write Extension' comes up. Everything else remains the same.

    Separate question, if anyone cares to respond:

    - Doesn't changing the value from -89 to -110 basically only lower the threshold signal level at which 4G will connect? In other words, doesn't this effectively tell the phone to connect to 4G even if the signal is as low as e.g., -110db? In that case, wouldn't the signal be weaker, and thus perhaps unable to achieve the 4G 'promised' data rates?

    Is it possible that -089db was thought to be the 'break-even' point, where below that signal level, 3G would perform as well or better?

    All of this is speculation on my part, because I don't even know what half the acronyms in the settings stand for, but I'm usually hesitant to follow a 'do THIS and THIS will happen' instruction without understanding the WHY behind it.

    Thx,

    Andy Capp
    10-25-2011 01:22 PM
38 12
LINK TO POST COPIED TO CLIPBOARD