Search results

That image puts a chill down my spine, watching Rambo last blood was easier;) They need a good case especially for corner protection on these almost no bezel look devices.

Smart man. I think you'll love it. A very versatile and fun device. It can be a pastime in its self... in a good way:)

Yes, yes I am :) Lol, if one can't fill in the blanks themselves, one shouldn't go blaming good intentioned remote 3rd parties for their own ineptness...

The main reason I get carrier variants and keep insurance of them until they are paid out :( A good case is important because it limits the G loading on the internal components; it helps protect them as well. Normally it takes hundreds of G's to damage them and the phone's outside covering adds...

If you can't send it in for warranty repair do so but short of that it sounds like it's now a parts queen. Sorry :(

I think it's an assembly issue; not making proper contact.

That is "rubbing" alcohol... >91% though is best

Don't touch the contacts. Clean with isopropyl on a Q-tip and carefully inspect them. If the replacement part is higher than the OEM if could distort the antenna PCB, eyeball it. Make sure it's making contact... try tightening the screw closest to the contacts first.

A component level or solder failure can happen at anytime. Manufacturing defects are inevitable. They are constantly dropped and suffer environmental insults throughout their life. It's amazing these miniature devices are as reliable as they are. It will take hands on by skilled tech with the...

Well I'm still looking. The screen needs protection from sand scratches. Any screen protector will help spread an impact better than no protector at all. The curved screen is demon to protect :( Too bad Samsung never supplied factory replacements... That's how hard aftermarket protectors are...

If you have a none root package blocker for LG (I think I've seen them) you can start disabling likely candidates and see if you can track it down. If it's a nonessential apk you could permanently disable it. Also go into Developer Options and see if any there's any help there. I doubt it...

When I get an open box special instead of new factory package one direct from Whitestone it tells me all I need to know. Never playing with these chintzy *Marine grade profanity* again... You really think this was the first time they did this?

My experience with Whitestone was a bloody nightmare. They sent an Apple screen in the Note 10+ box and well as the wrong tray which didn't fit either one. It was obviously an open box special Whitestone reabsorbed and at best did a parts count inspection. Customer support was just send it back...

My bad :( They apparently manually set theirs as well...

Your screen is showing exactly the same albeit the value. Since I manually entered it I think it's defaulting to that value; initially it was slightly lower. I corrected it. The correct rated capacity is what matters. It sets the baseline... ha-ha life's not fair.

Minimum acceptable level? I got that same screen on tutorial where you said to look. The set up is locked unless I delete the current data so it runs the set up again. Not sure what it's using maybe off the power controller or battery pack? Your screen shot shows that it was set manually as...

You maybe correct. I don't recall this screen... but... I'm normally in lala land on uncomplicated installs... give me the beef mode. There's no listing of this device anywhere in the app so it may never have self detected it. Started with the free version and left that data intact. There's no...

Hell yeah wait! That not just more memory, it's fast memory. Can't come close to it's R/W speeds with the best flash cards.

I have the paid version and there's no auto detect for the factory bat spec. Maybe so on some devices but certainly not this one, Note 10 plus running on Pie. After over 6 months it's best guess is 98% of its original capacity. It's gotten some heat and full charges but I've been conservative...

-You- have to set the size of the battery in Accubattery. Charging page>bottom of page, punch the Set Design Capacity button>enter rated bat capacity Without this data it can't do some functions properly... You may want to clear all data -before- you do the above as some the data it has...